Chopping Tobacco in 18th Century. USNM 19048; 1887. Korean farmers chopping tobacco after it has been cured. By Han Chin U. Gift of G. Goward, Washington, D. C.

5. Scene of Korean Farmers Working on Farm Buildings in Late 18th Century. USNM 19048; 1887. Korean farmers doing carpentry work, including roof repair. By Han Chin U. Gift of G. Goward, Washington, D. C.

6. Scene of a Korean Blacksmith at Work in Late 18th Century. USNM 19048; 1887. A Korean blacksmith working at his forge and anvil. By Han Chin U. Gift of G. Goward, Washington, D. C.

7. A Korean Farrier Shoeing a Horse in the Late 18th Century. USNM 19048; 1887. By Han Chin U. Gift of G. Goward, Washington, D. C.

8. Centrifugal Cream Separator, 1868. USNM 23744; 1890. The first centrifugal cream separator used commercially in the United States. The Deerfoot Farm at Southborough, Massachusetts, used this machine, patented by D. M. Weston of Boston. Gift of Deerfoot Farm Company, Southborough, Massachusetts.

9. Model of Blount's Daisy Plow, 1890. USNM 23873; 1891. This model of a one-horse plow shows Blount's Daisy steel plow as pictured in the catalog of Henry F. Blount. Gift of Henry F. Blount, Evansville, Indiana.

10. Old Colony Strong Plow, 1732. USNM 34769; 1899. In 1732 Peter Hardy of Raymond, New Hampshire, made this plow for Henry Lamprey of Kensington, New Hampshire. Gift of J. P. Lamprey, Kensington, New Hampshire.

Figure 1.—Views of Old Colony Strong Plow, about 1732. (Catalog No. 10.)

11. Winnowing Basket, 1799. USNM 37441; 1901. A winnowing basket, or pan, made of willow woven over wide sprints; elliptical in shape, with a frame of thick rods. Noah Rogers bought this pan in New York in 1799 or 1800. Gift of Frank A. Brown, Savage, Maryland.

12. Model of Flail Threshing Machine, 19th Century. USNM 46812; 1906. The frame of this wooden model is 7½ inches high and 5 by 6 inches, rectangular. The levers, 14 inches long, project from the frame and strike the floor much as a flail would. Pins set in the shaft of a hand crank act as cams, raising the flails which then fall to the ground by gravity. Gift of United States Department of the Interior.

13. Model of Gallic Grain Header, about a.d. 70. USNM 46812; 1906. A wooden box on wheels, 12 by 5 inches, has metal teeth set at the front end. Shafts extend to the rear, where an ox is yoked. The forward movement of the cart causes the grain to lodge against the teeth, which pulled the heads off. The grain then fell back into the box. Gift of United States Department of the Interior.

14. Model of Ten Eyck Grain Harvester, 1825. USNM 46812; 1906. Model is made of wood and iron, 15 inches by 8 inches. Long knives on a drum were rotated by belt shaft on traveling wheels. Long projecting points gathered the straw. Iron shafts at the rear allowed animals to be harnessed to push the machine. James Ten Eyck patented the harvester on November 2, 1825. Gift of United States Department of the Interior.

15. Model of Manning Grain Harvester, 1831. USNM 46812; 1906. Model of horse-drawn reaper measures 16 inches by 8 inches, with a wheel diameter of 6 inches. Projecting iron points at the front end gather the grain, and vibrating knives, powered from the hob of the wheel, cut the grain. Patented by William Manning on May 3, 1831. Gift of United States Department of the Interior.

16. Model of Boyce Grain Harvester, 1799. USNM 46812; 1906. This model, made of wood and iron, is 15 inches long, 6 inches wide, and 5½ inches high. Six rotating knives radically positioned on a vertical shaft rotate by level gearing on the wheel axle. The whole is mounted on a two-wheeled cart with shafts for draft animals. English patent number 2324 granted to James Boyce in 1799. Gift of United States Department of the Interior.

17. Model of Newbold Plow, 1797. USNM 46812; 1906. This model of a metal plow, with wooden beam and handles 14 inches long, represents the plow patented by Charles Newbold on June 26, 1797, the first American patent for a cast-iron plow. Moldboard, share, and landside were cast in one piece. If the plow broke, it became totally useless. Not until the parts were made in separate pieces did the iron plow come into wide use. The cast iron broke more readily than did the later wrought-iron plows. Gift of United States Department of the Interior.

18. Winnowing Basket, about 1750. USNM 54513; 1912. Used by the three Richardson brothers, the first settlers of Woburn, Massachusetts. The threshed grain could be winnowed in two ways. It could be poured slowly from the edge of the basket in a breeze, where the heavier grain fell to the ground while the chaff blew away. More commonly, the farmer tossed the grain into the air and caught it in the basket, while the chaff blew away. This rectangular basket measures 50 inches by 30 inches. Gift of Mrs. Clarissa W. Samson, West Medford, Massachusetts.

Figure 2.—De Laval centrifugal cream separator of 1879. (An earlier version of Catalog No. 19.)

19. Centrifugal Cream Separator, 1914. USNM 56432; 1914. Carl Gustav De Laval of Sweden invented this successful continuous-flow cream separator in 1879. Loaned by De Laval Separator Company, New York, New York.

20. Model Tractor, 1919. USNM 64098; 1919. No particular manufacturer seems represented by this spring-driven toy, which merely represents tractors of around 1919. The heavy-duty field tractor has four widely spaced iron wheels. Gift of Toy Manufacturers of the United States, New York, New York.

21. Model Tractor with Plow, Harrow, and Roller, 1919. USNM 64098; 1919. Spring-driven, toy tractor. The plow, harrow, and roller, as well as the tractor itself, represent a typical machine of the period. The product of no particular firm seems to have been copied. Gift of Toy Manufacturers of the United States, New York, New York.

22. Meat Grinding Machine, about 1810. USNM 110326; 1930. Hand made of wood and iron, with six parts held together by two iron bolts. The cutting edges are set in the sides of a box parallel to each other and about one-quarter inch apart. A shaft, set in the center of the box, is turned by a crank. The horizontal shaft has iron slugs, graduated from coarse to fine, set into the shaft in a helical pattern. The meat enters through the square hole at the top and the iron teeth press it against the knife edges; thus, the meat is cut smaller and smaller until it comes out a small hole in the bottom of the machine. The device is very ancient in design