when at sea, and the forward shroud should be matted or battened all the way up to the futtock staves.

In some smaller merchantmen the lower rigging is not infrequently set up upon its end to bolts in the rail. This is very inconvenient on many accounts, especially as all the seizings have to be come up with, and the nip of the shroud altered, whenever it is at all necessary to set them taut. This soon defaces and wears out the ends; while, with dead-eyes, only the lanyards have to be come up with. Some vessels set up their lower rigging with dead-eyes upon the rail. This is convenient in setting them up in bad weather, but does not give so much spread as when set up in the channels, and presents a more complicated surface to the eye. If the rigging is fitted in this way, you must deduct the height of the rail above the deck from the measure before given for cutting it.

Breast-backstays.—It is not usual, now, for merchant vessels to carry topmast breast-backstays. If they are carried, they are spread by out-riggers from the top. Topgallant and royal breast-backstays are used, and are of great assistance in sailing on the wind. There are various ways of rigging them out, of which the following is suggested as a neat and convenient one. Have a spar fitted for an out-rigger, about the size of one of the horns of the cross-trees, with three holes bored in it, two near to one end, and the third a little the other side of the middle. Place it upon the after horn of the cross-tree, with the last-mentioned hole over the hole in the end of the horn of the cross-tree, and let the after topgallant shroud reeve through it. Reeve the topgallant and royal breast-backstays through the outer holes, and set them up by a gun-tackle purchase, in the channels.[1] The inner end of the out-rigger should fit to a cleat, and be lashed to the cross-tree by a lanyard. When the breast-backstays are to be rigged in, cast off the lanyard, and let the out-rigger slue round the topgallant shroud for a pivot, the inner end going aft, and the outer end, with the backstays, resting against the forward shroud. One of these out-riggers should be fitted on each side, and all trouble of shifting over, and rigging out by purchase, will be avoided.

CHAPTER III.

FITTING AND REEVING RUNNING RIGGING.

Fore braces. Main braces. Cross-jack braces. Fore, main, and mizzen topsail braces. Fore, main, and mizzen topgallant and royal braces. Trusses. Topsail tyes and halyards. Topgallant and royal halyards. Peak and throat halyards. Spanker brails. Fore and main tacks and sheets. Topsail, topgallant and royal sheets and clewlines. Reef-tackles. Clew-garnets. Fore and main buntlines, leechlines, and slablines. Topsail clewlines and buntlines. Bowlines.

To reeve a brace, begin on deck, and reeve to where the standing part is made fast. The fore braces reeve up through a block on the mainmast just below the rigging, down or in through the brace-block on the yard or at the end of the pennant, and the standing part is brought through the cheeks of the mast with a knot inside. The neatest way for reeving the main brace is out through a single block on the brace-bumpkin, out through the brace-pennant-block, in through an outer block on the bumpkin, and seized to the strap of the pennant. Another way is out through the bumpkin block, out or down through the pennant block, and secure the end to the bumpkin or to the fashion-piece below.

The cross-jack braces reeve up through blocks on the after shroud of the main rigging, up through blocks on the yard, one third of the way in from the yard-arm, and are seized to a bolt in the mainmast, or to the after shroud again.

The fore topsail braces reeve up through the blocks secured to the bibbs at the mainmast-head, in through the span-block at the collar of the main stay, up through the block on the yard, and are seized to the main topmast-head; or else up through a block at the topmast-head, down through the brace-block on the yard, and are seized to the collar of the main stay. The last way is the best. The main topsail braces are rove through span-blocks at the mizzen-mast, below the top, up through the blocks on the yard, and are seized to the mizzen topmast-head; or else up through a block at the mizzen-mast-head, down through the block on the yard, and secured to the mizzen-mast. The first way is the best. The mizzen topsail braces reeve up through the leading blocks or fair-leaders on the main rigging, up through blocks at the mainmast-head, or at the after part of the top, up through the yard blocks, and are seized to the cap.

The fore and main topgallant braces are rove up through blocks under the topmast cross-trees, in through span-blocks on the topmast stays, just below their collars, up through the blocks on the yards, and the main are usually seized to the head of the mizzen topgallant mast, and the fore to the topmast stay, by the span-block. The mizzen topgallant braces generally go single, through a block at the after part of the main top-mast cross-trees. The royal braces go single: the fore, through a block at the main topgallant mast-head; the main, through one at the mizzen topgallant mast-head; and the mizzen, through a block at the after part of the main topmast cross-trees.

Halyards.—The lower yards are now hung by patent iron trusses, which allow the yard to be moved in any direction; topped up or braced. The topsail yards have chain tyes, which are hooked to the slings of the yard, and rove through the sheave-hole at the mast-head. The other end of the tye hooks to a block. Through this block a chain runner leads, with its standing part hooked to an eye-bolt in the trestle-tree, and with the upper halyard-block hooked to its other end. The halyards should be a luff purchase, the fly-block being the double block, and the single block being hooked in the channels. Sometimes they are a gun-tackle purchase, with two large single blocks. The lower block of the mizzen topsail halyards is usually in the mizzen-top, the fall coming down on deck.

The fore and mizzen topsail halyards come down to port, and the main to the starboard. The topgallant halyards come down on opposite sides from the topsail halyards; though the fore and main usually come down by the side of the masts. The fore and main topgallant halyards sometimes hoist with a gun-tackle purchase, but the mizzen and all the royal halyards are single.

The throat and peak halyards of the spanker are fitted in the following manner. The outer peak halyard block is put on the gaff, one third of its length from the outer end, or a very little, if any, within the leech of the sail; and the inner one, two thirds in. The blocks are fitted round the gaff with grommet straps, and are kept in their places by cleats. The double block of the peak halyards is strapped to the bolt in the after part of the mizzen cap, and the halyards are rove up through this, in through the blocks on the gaff, the inner one first, the standing part made fast to the double block, and the fall coming on deck. The upper block of the throat halyards is secured under the cap, and the lower block is hooked to an eye-bolt on the jaws of the gaff. This is a two-fold tackle.

The Spanker Brails.—The peak brails reeve through single blocks on the gaff, two on each side, generally span-blocks, and then through the throat brail blocks, as leaders, to the deck. The throat brails reeve through