them flat with an ordinary pair of pliers; or by {35} cutting a piece of quill the shape of the body from a turkey or goose wing. Bind this on top of the hook for the foundation of the body, and build the body over this. When finished, lacquer the entire body.

Most any body materials that are used for the making of other flies can be used; however, wool is mostly used for nymphs. Silk floss wound over a quill foundation and then lacquered, makes a very smooth, realistic body.

{36}

Diagram 6

{37}

THEIR CONSTRUCTION (SEE DIAGRAM 6)

Start tying silk (A) an eighth of an inch from the eye of the hook and wind closely down shank, as previously done with bucktails, wet flies etc. Next cut a section (B) from a grey goose wing feather about one eighth inch wide, and tie on top of the hook as Fig. 1. This is to make the tail and also the back of the nymph. Bend (B) back and take a turn or two with (A) in front as Fig. 2. Tie in the ribbing (c) close to (B) Fig. 3. Next tie in body material (D) close to (C) Fig. 4. Wool yarn makes the best body material for this style nymph. Now finish the body as for a wet fly, Fig. 5, then pull (B) tightly over the top, finish off as Fig. 6. This makes a sort of hard shell over the back. Next turn the hook upside down in the vise, and lay three horse hairs across, just in back of where the head is to be made, crisscross (A) between the hairs to spread them and make them look like legs, and your nymph should look like Fig. 7. Nymphs of this style as well as Figs. 8, 9, 10, 14 and 15 look more natural if the bodies are flattened. Fig. 8 is tied nearly the same as Fig. 7, the difference being that (C) and (D) are both wound over (B) about two-thirds of the length of the body, then (B) is turned back, the body finished as before, (B) brought forward loosely to form the humpbacked wing case, and (B) being cut off as was done with Fig. 6, and instead of the butt end of (B) being cut off as was done with Fig. 6 it is split by crisscrossing (A) through it to form small wings as Fig. 8. Fig. 9 is made in the same way except that several strands of peacock herl is used for the dark back, tail, and feelers.

Fig. 10 is a very effective nymph, the body made entirely of natural raffia (soaked in water before using), with black hair used for the tail and feelers The body coated with lacquer as before mentioned and pressed flat when dry; paint the back with dark brown or black lacquer.

Fig. 11 is made by close wound palmer hackle cut off on dotted lines. Fig. 12 is a fur body, made by spinning rabbit's fur or other fur on waxed tying silk and ribbing with gold; the tougher this nymph looks the more effective it seems to be. Fig. 13, the Caddis {38} worm can be more naturally reproduced with a common rubber band than any other way I know. Get a dirty, white, rubber band about 1/8" wide, taper one end for about 1/2". Lay two horse hairs lengthwise on top of the hook for the feelers, wind tying silk over them down the hook, tie in the rubber band by the very tip of the taper, wind the tying silk back to the starting point, and be sure that the tying silk is wound smoothly. If not, any roughness will show through the rubber band. Wind the rubber band tightly to about 1/4" back of the eye. Wind back down and take one turn under the horsehair at the tail end, wind up to the head and tie off with the tying silk. This now makes three thicknesses of the rubber band. Form a large head with the tying silk, fasten securely and you have a very realistic Caddis worm. Fig. 14 is tied about the same as Fig. 7, with a considerable amount of speckled mallard, and peacock herl used for both the front and back feelers as well as the legs.

Fig. 15. The Damsel Nymph has a body of dark grey wool with a back of dark brown or black lacquer. Wings, small red-brown wood duck breast feathers, feelers dark brown hackle, and a large black head.

{39}

THE HELGRAMITE (SEE DIAGRAM 7)

The Helgramite Nymph, larva of the Dobson Fly, is such an excellent bass and trout food, that the making of this nymph deserves special mention. As my personal way of making this particular nymph differs considerably from those previously explained, I consider it advisable to go into further details concerning the construction of this pattern.

I personally like the winged style. That is, with small imitation wings and horns, or feelers. This represents the nymph in its final underwater stage, just before emerging from the water as the Dobson Fly. I find black skunk tail the most satisfactory material for the body of this nymph. Either light grey swan sides, or light grey pigeon breast feathers for the wing and legs.

{40}

Diagram 7